
Reference: 075040
Brand: Indasa
Red Line Diam 75 mm Self-gripping Disc
Red Line Diam 75 mm Self-gripping Disc
Reference: 075040
Brand: Indasa
Red Line Diam 75 mm Self-gripping Disc
Reference: RF751500
Brand: Indasa
SPECIAL SKIN OF ORANGE FILM DISC P500/800/1500 DIAM 75
Reference: 3M50413
Brand: 3M France - Marine Auto
Disques de dépolissage et de raccord 3M™ Trizact™
Reference: FE180
Brand: Indasa
WATERPROOF GRAIN SHEET 180 A 1500Our waterproof abrasive sheets will allow you to make a wet sanding or polished glossy and thus take back paint defects, essentially an orange peel.
Reference: FE2500
Brand: Indasa
WATERPROOF SHEET GRAIN 2000 or 2500 - 1/2 SHEETOur waterproof abrasive sheets in 2000 or 2500 grain will allow you to make a wet sanding (wetsanding) and thus take back paint defects, essentially an orange peel.
Das-6 PRO
Clay deContamination Medium
100 GR
Allows the decontamination of a surface before polishing
(to be changed in the "Reinsurance" module)
(to be changed in the "Reinsurance" module)
(to be changed in the "Reinsurance" module)
The decontamination clay DAS-6 PRO medium allows the removal of contaminants on the surface of the body (varnish, lacquer, glass).
Thanks to its special detailing formula, it limits defects due to application (marring).
You can treat different types of contaminant with our clay (bird droppings, paint trace, oxidation, tar, ...).
Before polishing a vehicle, we will of course wash it.
If we are rigorous, we will do a pre-wash and then a manual wash with a neutral shampoo.
But have we removed all the contamination present on the vehicle?
Each wash will remove much of the dirt.
Problem. A big part? But not everything?
And no. The smallest dirt is always there, nesting in imperfections of the varnish. If you run your hand over your body, you feel it, at least you do not feel a smooth surface, but a very slight roughness, nothing important because it is not visible, but important enough to threaten our polishing.
Indeed, when we start our correction with our polisher, our pad with its polish will be in contact with its microparticles and with their strength will tear them from the bodywork. They will nestle inside the pad and will act on our correction by bringing their aggressiveness as dust and voila, we make holograms during our polishing.
We chose an orbital polisher to have as few defects as possible and yet we create some.
Nothing is lost, it is easy to remove this contamination.
Plan a lubricant or make it yourself:) with 1 liter of demineralized water in which you will put 2 or 3 caps of your favorite shampoo.
Knead your clay in your hand to soften it and create a washer about 7 to 8 cm in diameter.
Spray your lubricant on your clay and on the surface to be treated (wear gloves).
Gently rub your clay on the surface. Lubricate regularly.
5 /5
Based on 1 customer reviews
Sébastien B. published the 14/03/2023 following an order made on 23/02/2023
Nickel
Reference: 137414 x 12
Brand: Intercash Professionnel
CHIFFON MICROFIBRE 40 X 40 batch of 12
Reference: 66445
Brand: Krauss Tools
Sprayer 710 ml Chemical Resistant with Viton Seal
Reference: 615300374x10
Brand: Intercash Professionnel
Lot of 10 CHIFFONS Micro Fibers LASER POLISH blue 400 g/m2 40 X 40
Reference: BLM05006
Brand: BLACKMAMBA
Black BlackMamba Nitrile Black Gloves - Size L - Box of 100
Reference: DAS245
Brand: DAS-6 PRO
Das-6 PRO Hard Decontamination Clay100 GRAllows the decontamination of a surface before polishing
Reference: DAS247
Brand: DAS-6 PRO
Das-6 PRO Fine Decontamination Clay 100 GRAllows the decontamination of a surface before polishing
Das-6 PRO
Clay deContamination Medium
100 GR
Allows the decontamination of a surface before polishing